Decibels and Sound Level: What the Numbers Really Mean
How the logarithmic decibel scale works, why +3 dB doubles power but not loudness, what dBA means, and how to read noise limits and everyday sound levels.
Few units cause as much confusion as the decibel. A quiet library, a lawnmower and a rock concert might differ by only a handful of numbers on a label, yet the sound energy between them differs by factors of millions. The reason is that the decibel is not a measurement of a physical quantity so much as a way of comparing two quantities on a logarithmic scale. Once you grasp that, the rest follows.
A ratio, not a unit of its own
The bel, named after Alexander Graham Bell, is the logarithm to base ten of a power ratio. The decibel is a tenth of a bel, and it is the version people use. For power quantities:
level in dB = 10 × log10(P / Preference)
Because the result depends on a ratio, you always need a reference. A figure such as “70 dB” is meaningless on its own. It must be 70 decibels relative to something, and the something is usually written in the unit’s suffix or understood from context.
Why a logarithm
Human hearing covers an enormous span. The loudest sound the ear tolerates briefly carries something like a trillion times more power than the faintest we can detect. Writing that as plain numbers would be unwieldy, and our perception of loudness is also roughly proportional to the logarithm of intensity rather than the intensity itself. A log scale compresses the span into numbers from about zero to a little over a hundred and matches how sound is experienced.
The three numbers to memorise
- +3 dB means roughly double the power (the exact factor is 1.995).
- +10 dB means ten times the power.
- +20 dB means one hundred times the power.
Quantities such as sound pressure and voltage are field quantities, and power goes with their square. That is why the formula changes to 20 × log10(ratio) for pressure or voltage. The consequence is that doubling sound pressure adds about 6 dB, while doubling sound power adds about 3 dB. Both statements are correct; they describe different quantities.
Sound pressure level and its reference
When people speak of noise in decibels, they usually mean sound pressure level (SPL) in air, measured against a reference pressure of 20 micropascals. That value is close to the quietest sound a young healthy ear can detect at mid frequencies, so 0 dB SPL sits near the threshold of hearing. It does not mean silence; sound at 0 dB SPL can exist, and negative levels are possible.
Some approximate everyday levels, which vary by situation and should be taken as ballpark figures:
| Source | Typical level (dB SPL) |
|---|---|
| Rustling leaves, very quiet room | about 20 |
| Normal conversation | about 60 |
| Busy road at a distance of a few metres | about 70 to 85 |
| Power tools and loud concerts | about 100 to 110 |
| Threshold of pain | roughly 120 to 130 |
What the A in dBA means
The ear is not equally sensitive at all frequencies. It hears mid-range tones well and low rumbles poorly, especially when sounds are quiet. A-weighting is a filter that reduces the contribution of low and very high frequencies so that a meter’s reading resembles human response. Noise regulations and product ratings are normally given in dBA. C-weighting, which is flatter, is used for very loud sounds and peak measurements, and plain unweighted readings are sometimes written dBZ or dB(lin).
Adding and combining sources
Decibels do not add like ordinary numbers. Two identical machines each producing 60 dB together produce about 63 dB, not 120, because the power doubles and doubling is +3 dB. Ten identical sources raise the level by 10 dB. If one source is much louder than another, the quieter one barely matters: a 70 dB source combined with a 60 dB source gives about 70.4 dB.
Distance and the inverse-square law
In open space with no reflections, sound from a small source spreads over a sphere. Each doubling of distance quarters the intensity, a fall of about 6 dB. Standing four metres from a source instead of two therefore reduces its level by around 6 dB, and eight metres cuts it by about 12 dB. Indoors, reflections reduce that benefit, and walls or hard floors can keep the level higher than the formula predicts.
Perceived loudness is not the same as level
A common rule of thumb says that a rise of about 10 dB is heard as roughly twice as loud. It is only an approximation, and it holds best for mid-range sounds at moderate levels. A change of 1 dB is barely noticeable under ideal conditions, while 3 dB is clearly noticeable though modest. Fixed numbers will not capture the detail of individual hearing, so use them as guidance only.
Workplace limits and the exchange rate
Hearing damage depends on both level and duration. NIOSH in the United States recommends an exposure limit of 85 dBA over eight hours, and each 3 dB increase halves the permitted time. OSHA’s permissible exposure limit is 90 dBA over eight hours and uses a 5 dB exchange rate. Many other countries set action levels in a similar range. If your work involves regular loud noise, check the rules that apply where you are rather than relying on a rule of thumb.
Other decibel scales you will meet
- dBm is power relative to one milliwatt, common in radio and fibre optics.
- dBV and dBu express voltage relative to fixed references and appear on audio equipment.
- dBFS is level relative to the digital full scale of a recording system, so peaks cannot exceed 0 dBFS without clipping.
- dBi and dBd describe antenna gain compared with reference antennas.
The suffix tells you what was compared. Adding or subtracting decibels is straightforward when they share a reference. A gain of +6 dB applied to a signal at −20 dBm yields −14 dBm, because applying a gain is the same as multiplying the ratio.
Converting decibels back to ratios
To reverse the calculation, raise ten to the power of the level divided by ten for power, or by twenty for voltage and pressure. A gain of 30 dB is a power ratio of 1,000 and a voltage ratio of about 31.6. Keep track of which version applies, because applying the wrong one is the most common error.
Rule of thumb: every 3 dB is a doubling of power, and every 6 dB is a doubling of pressure or voltage. Once you remember those two facts, most decibel questions can be answered in your head.
Frequently asked questions
Is 0 dB the absence of sound?
No. For SPL it is the reference level, close to the threshold of hearing. Quieter sounds have negative decibel values.
Why does a 3 dB increase matter so much?
Because it represents double the acoustic power, which for protecting hearing means the safe exposure time is halved under the NIOSH approach.
What is the difference between dB and dBA?
dBA applies a weighting that mimics the ear’s sensitivity, which is why it is used for noise limits.
How much quieter is a sound that is 20 dB lower?
It has one hundredth of the power and one tenth of the sound pressure.
Can a phone app measure decibels accurately?
Apps are useful for rough checks, but phone microphones and processing differ, so legal or occupational measurements require a calibrated meter.
For related electrical and power ratios, see our power converter.