Home / Articles / Technical Reference

Technical Reference · 5 min read

By The Convertthisnow Editorial Team

Aviation Altitude: Feet, Flight Levels and Altimeter Settings

Why aircraft altitude is quoted in feet, how flight levels and altimeter settings work, and how a small pressure error becomes hundreds of feet of height.

Ask a pilot how high they are flying and the answer comes in feet, even in countries that otherwise use metres for everything from roads to rainfall. Aviation altitude is one of the best examples of a unit system that is deliberately held constant across borders. But the more interesting part is not the unit itself; it is that "altitude" in aircraft terms has several meanings, each tied to a pressure reading rather than a tape measure. Understanding that is the key to reading altitude figures correctly.

Several meanings of "height"

These terms sound alike and are easy to mix up:

  • Elevation — the height of a point on the ground above mean sea level.
  • Altitude — height of the aircraft above mean sea level, as indicated by the altimeter set to local sea-level pressure.
  • Height — vertical distance above a specified ground point such as the runway.
  • Pressure altitude — the altitude shown when the altimeter is set to the standard reference pressure, 1013.25 hPa or 29.92 inches of mercury.
  • Flight level — pressure altitude in hundreds of feet, written FL, so FL350 means 35,000 feet on the standard setting.

A barometric altimeter does not measure distance at all. It is a sensitive pressure gauge whose dial is marked in feet, using a model of how air pressure falls as you climb. That model is the International Standard Atmosphere: 15 °C and 1013.25 hPa at sea level, cooling by 6.5 °C per kilometre up to about 11 kilometres.

Why feet?

The reason is mostly history and coordination. Early aviation grew up in the British and American spheres, where feet were the working unit, and when the International Civil Aviation Organization published its standards, feet were adopted for altitude and elevation alongside knots for speed. ICAO does list the metre as the SI-based alternative, and a few states have used it domestically for long periods, but the cost of a worldwide change would be large and the safety case is weak. Pilots, controllers and aircraft instruments all work in feet, and changing midway through a flight would create precisely the confusion that standards exist to prevent.

For reference, one foot is exactly 0.3048 metres, so a pilot at 10,000 feet is at 3,048 metres.

Setting the altimeter

Because the atmosphere's pressure changes with weather, the altimeter has a small knob to set a reference pressure. Three settings appear in aviation vocabulary:

  • QNH — the local pressure reduced to mean sea level. With QNH set, the altimeter reads altitude above sea level, and on landing it shows the airfield's elevation.
  • QFE — the pressure at the airfield itself. With QFE set, the altimeter reads height above the airfield, and zero on the runway.
  • QNE — the standard setting, 1013.25 hPa. This is what makes flight levels possible.

In North America the setting is quoted in inches of mercury, for example 29.92, while most of the world quotes hectopascals. Mixing these up is dangerous because the numbers look nothing alike, which is itself a protection.

Transition altitude and flight levels

Below a certain height, aircraft use local QNH so that altitude relates sensibly to terrain and obstacles. Above it, everyone sets 1013.25 hPa, so that all aircraft share one reference and keep their separation even when the true pressure differs from place to place. The switching boundary is called the transition altitude; the lowest usable flight level above it is the transition level. In the United States the transition altitude is 18,000 feet. Many other countries set it lower, and some airports define their own.

Flight levelPressure altitude (feet)Metres
FL0505,0001,524
FL10010,0003,048
FL18018,0005,486
FL29029,0008,839
FL35035,00010,668
FL41041,00012,497
A flight level is not a measured height. An aircraft at FL350 on a low-pressure day may be well under 35,000 feet above the sea, and that is acceptable because everyone nearby is flying the same pressure surface.

How small pressure errors become big height errors

Near sea level, pressure drops by roughly 1 hPa for every 27 to 30 feet of climb. That makes the setting extremely consequential. If the altimeter is set to 1013 when the true QNH is 1003, a 10 hPa mismatch produces an error of around 270 to 300 feet. And the error is in the dangerous direction: the aircraft is lower than the instrument says. Pilots remember this with an old rhyme about flying from high to low pressure and looking out below.

The same arithmetic applies to inches of mercury: one inch corresponds to roughly a thousand feet. Setting 29.92 instead of 29.42 shifts the indicated altitude by about 500 feet.

Density altitude

Pressure altitude feeds into another quantity that matters for performance. Density altitude is the altitude in the standard atmosphere at which the air density would match today's actual density. A common rule of thumb adds about 120 feet to pressure altitude for each degree Celsius the temperature is above standard.

Example: an airfield at 5,000 feet with standard pressure has a standard temperature of roughly 5 °C. On a 30 °C afternoon that is 25 degrees warmer, so density altitude is approximately 5,000 + (25 × 120) = 8,000 feet. The aircraft behaves as though it were at 8,000 feet: the engine produces less power, the wings need a longer take-off roll, and climb rate falls. Hot, high airfields are where this matters most.

Cabin altitude and vertical separation

Two other altitude concepts show up in everyday travel. Cabin altitude is the pressure equivalent inside the aircraft. Airliners fly outside at tens of thousands of feet but pressurise the cabin so that passengers experience something closer to a mountain town, and regulations limit the maximum cabin altitude in normal operation to 8,000 feet.

The other is vertical separation. Between FL290 and FL410, certified aircraft in approved airspace are separated by 1,000 feet rather than 2,000, a system called reduced vertical separation minimum, in use widely since the late 1990s. It lets airspace hold more traffic, but it demands accurate altimetry, which is why the instruments are regularly tested.

Quick conversions and takeaways

  • Metres = feet × 0.3048. A fast approximation: divide feet by 3.3.
  • Flight level × 100 = feet. FL330 is 33,000 feet.
  • Altimeter error ≈ 27–30 feet per hPa near sea level.
  • Density altitude ≈ pressure altitude + 120 × (temperature above standard, in °C).

Our length converter turns feet into metres and kilometres, and the pressure converter handles hectopascals and inches of mercury.

Frequently asked questions

Why do flight levels start at a pressure setting rather than true height?

Aircraft near one another need a shared reference. A common pressure surface guarantees that, even if the surface is not at a constant true height.

Is altitude on a flight tracker accurate?

Usually it shows pressure altitude reported by the aircraft, so it may differ from true height above the sea.

Do any countries use metres for altitude?

Some have done so for domestic or military airspace, which is why pilots crossing certain borders have historically had to convert. International traffic overwhelmingly operates in feet.

What is a radio altimeter?

It measures true height above the ground by timing a radio signal. It is used on approach, separate from the pressure-based instrument.

About the author. Articles are researched and written by the editorial team at DukaMoja Digital, LLC, checked against standards-body definitions (BIPM, NIST) where relevant, and updated when figures or conventions change. Spot an error? Email hello@convertthisnow.com.